Old Bus Photos

Ideal Service – Leyland Titan PD2 – YWT 572

lowbridge_lower_deck_fwd_lr
Lower deck facing forward

Ideal Service (R Taylor & Sons) - Leyland Titan - Lowbridge - Lower Deck
Lower deck facing rearward

Ideal Service (R Taylor & Sons) - Leyland Titan - Lowbridge - Upper Deck
Upper deck facing forward

lowbridge_upper_deck_back_lr
Upper deck facing rearward

Ideal Service (R Taylor & Sons)
1959
Leyland Titan PD2 (on older Tiger PS1 chassis)
Roe L27/28R

My thanks to Robert Gomersall for these excellent internal shots of a newly delivered Roe bodied Titan to R Taylor & Sons of Cudworth near Barnsley who along with H Wray & Sons of Hoyle Mill operated under the name of Ideal Service. Roberts mother was the daughter of R H Taylor who took over operations from his father R Taylor who started the business. Robert would like to know when R Taylor actually started the business, if you know please leave a comment.
The lower deck is of a normal layout for a rear entrance double decker, but as this is a lowbridge vehicle it as a sunken gangway on the right hand side of the upper deck which can be seen quite clearly in the upper deck shot.
The seats as can be seen are just two normal two seat units put side by side, looking closely at the shot it looks as if the right hand pair is set back a little, probably to aid passengers getting past from the left hand seats. I am not sure if there was ever a one piece four seat unit, if you know please leave a comment. The sunken gangway can also be seen upper left in the 2nd lower deck shot and people sitting in the seats underneath it had to be careful when getting up as you could quite easily end up with a nasty bump on the head.
I think these shots are extremely good as there is a lot of people who will of never seen a lowbridge vehicle seating layout, thanks again Robert.

Photographs contributed by Robert Gomersall


Born and bred in lowbridge country, I imagined till the age of eight that a central aisle upstairs was for trolleybuses only. A family trip to London taught me otherwise, but I continue to defend the lowbridge design against all its critics: it survived in production for over forty years essentially to Leyland’s 1927 design. Reading Corporation’s two batches (1956-57) of Regent IIIs originally had 27 seats upstairs (six fours and a three) but were later upseated to 31 on top, with all the fours now staggered just as in the R. Taylor PD2. I think the main point was to discourage generously-upholstered mortals from claiming more than their allotted 17 inches of seat-width.
Last week I was (silently) grumbling that lowbridge Roe-bodied buses never turn up at Southern rallies, as I wanted to see the internal details, and here we have Robert G’s superb shots! A prayer answered.

Ian Thompson


These buses look unusually uncluttered and spacious, minus stanchions. As for bench seats in the upper saloons of lowbridge buses, London Transport inherited six ST’s with bodies by Short Bros. of Rochester. These had a sunken gangway EITHER side and bench seats for THREE. It also had the Godstone STL’s which had one sunken gangway, but seats in alternate rows of THREE and FOUR. I never travelled on them, and, although they had rounded tops to the seats, I don’t know whether they were bench seats or not. LT’s few lowbridge D’s (Daimler CWA6’s) had a sunken gangway with bench seats for FOUR. The first batch came with austerity wooden slatted seats, which would have caused some instability in passengers when going around corners. Even on similar double seats, one rode by the seat of one’s pants (so to speak) around corners, I recall!

Chris Hebbron


Another operator sadly missed! I was fortunate enough to travel on the Ideal Service in the early 70’s although by then it was being operated by H Wray alone. These photos are interesting because I hadn’t realised that a new double decker had been purchased as late as 1959. Logically it should still have been operating in 1970 although I don’t believe Wray took over any of Taylors vehicles when they decided to cease operating. I remember walking down to Hoyle Mill from Barnsley a few times to have a look at Wray’s operation and it was seemingly just an open yard with an inspection pit, I don’t recall seeing any covered accommodation! I think at the end, Wray had 3 or 4 double deckers, (perhaps always so) I remember travelling on a lowbridge AEC Regent V/Park Royal (ex Western Welsh?) an early Lodekka (ex W Yorks) and the last vehicle purchased, a Dennis Loline/Alexander, this giving the service a (fairly) modern image at last but unfortunately not for long! I’m not sure but I think that Wray, unlike Taylor, never purchased a new vehicle, and in the last few years tried to make sure their buses were from ‘red’ fleets to avoid the cost of re-painting! I’d love to know what became of YWT 572 because I’m sure there would have been plenty of miles left in it when Taylor sold up.

Chris Barker


What magnificent pictures these are and greatly appreciated. The vehicle is obviously assembled from the same Roe components as Samuel Ledgard’s six AEC Regent Mark Vs in 1957 – the panels, windows and frames, seats etc being identical. The only differences appear to be, obviously, the lowbridge layout and the rather luxurious light fittings. Good naturedly though, I must contest Ian’s praise of the lowbridge layout – while it undoubtedly solved the problem of height clearances such vehicles were very difficult for conductors, especially tall ones like me, and tended to roll alarmingly to the nearside if heavily laden and on badly cambered roads. By the way, West Yorkshire Road Car Co Ltd also experimented briefly in the 1950s with staggered upper saloon seating on lowbridge ECW Bristol KSWs.

Chris Youhill


I was fortunate enough, at the weekend, to combine a family gathering with a visit to the Sheffield Rally. In turn I was able to travel on STD 1156 (PD2/30) bodied by my beloved C H Roe. It was superb, albeit highbridge, but in every other respect, bar one, like these interior shots. [It has platform doors and an emergency door.]
The Leyland design was patented and could not originally be copied without buying a licence. Although, at that time, AEC did not have their own bodyworks, the blessed Mr Rackham had strong ideas about body design leading to certain stipulations for pre-war bodywork on AECs. Qs, therefore, like LTPB RTs after them, had very similar bodies regardless of Coachbuilder or operator. Likewise, Regents had the "Camel Hump" body for low-bridge operations. This was achieved by having gangways on both sides, three seats in a row and – conveniently – avoiding any infringement of the Leyland patent.

David Oldfield


Robert Taylor & Sons (Ideal Services) was taken over by the Yorkshire Traction. The Estate account shows Goodwill was £5700; Motor Vehicles £3025. Unfortunately it doesn’t itemise the vehicles sold.

Robert Gomersall


Just a couple of further points, a photograph of this vehicle in service appears on the Huddersfield Passenger Transport Group website, Buses in Barnsley section. It is not a PD2 but a re-bodied PS1. H Wray had one re-bodied in 1956 with a Roe body of Park Royal appearance which became KHE 528 and Taylor had this one done in 1959, both previously had Wilkes & Meade coach bodies. The earlier one was probably tagged on to a batch being done for Yorkshire Traction at the time. All of them were re-registered, maybe the Yorkshire Traffic Area was strict about such matters!
Apparently this vehicle passed to H Wray in 1967 so presumably this was the year that Taylor ceased operation.

Chris Barker


I read somewhere that the staggered upstairs seating was a standard ECW option towards the end of traditional lowbridge vehicles (mainly KSWs I think). It was said to improve access, but I would have thought the reverse – inside passengers having to jiggle round the S-bend as well as clambering over the knees of the outside passengers (or more likely asking them to move out).

Stephen Ford


03/08/11 – 15:57

Anyone know if the operators which made up Ideal Service were ever involved in a proposal to extend through to Pontefract the no. 70 Sheffield – Upton service? This would have been a more logical terminus and would have required one extra bus.
I worked for "Tracky" in the 70s and remember Ideal (by then , Wray only) running an ex-Bristol Omnibus Lodekka in the THW series. (However see above the comment about red fleets!)

Geoff Kerr


01/02/12 – 16:29

‘Yours’ Magazine Issue 133 (January 2012) has an interesting article written by a family member of Ideal Services (R H Taylor and Sons) complete with prints for those who are interested.

David Allen


02/02/12 – 09:10

Chris B, the re-registering of this fascinating vehicle is somewhat of a mystery as the Yorkshire Traffic Commissioners did not insist on the practice. I may be way out here, but I have a vague memory that if an operator wished to have a "prestigious" modern number the rebuilt vehicle had to have new chassis frames to be eligible, although the original number could be retained out of choice. Can anyone else remember such a ruling please ??

Chris Youhill


02/02/12 – 11:20

Chris Hebbron mentions how uncluttered the interior looks without stanchions and handrails. at Northern we were instructed not to allow standing passengers on coaches or DP’s because they didn’t have handrails, and if you look at the photo where the capacity is visible no mention is made of standing. Does anyone know if this was law or just Northern’s policy not to allow standing?

Ronnie Hoye


02/02/12 – 15:09

I believe Nottingham’s Roberts bodied AEC Regents had no stanchions. However the seats had a profiled back that was higher than these, and a grab-rail along the (straight) top which standees could hang on to. They allowed the usual maximum of 5 standing. I suspect that stanchions were not just for passenger convenience, but also provided a degree of bracing against bodyshell deformation. The Roberts bodies were of notoriously substantial build, and may not have needed this strengthening. I seem to remember that in the railway field the stanchions on the Class 150 DMUs figured in calculation of the bodyshell’s structural integrity.

Stephen Ford


02/02/12 – 17:23

I cannot remember stanchions in buses like this. I think you hung on to the seat back grab: perhaps there wasn’t room in a 7ft 6in body. You just walked "hand over hand" on the seat grabs down the aisle. Not only are the seats unusual, but finished in moquette: upstairs were often leather-type- I always thought because of ciggy burns and filthy overalls.

Joe


03/02/12 – 06:30

I’ve just noticed a most remarkable feature no doubt confined to the lowbridge version of this model of body. The lower saloon heater assembly is of greater width at the nearside to allow it to fit clear of the sunken gangway !!

Chris Youhill


03/02/12 – 10:33

Interesting observation, Joe. I can’t ever, down south, riding on any buses with leather/rexine seats upstairs (open-top and austerity ones excepted, of course). All were moquette. And London trams were the same. Yet there were plenty of dirty jobs in London. I suppose there were special floors ‘oop north’ta cater fer clogs, not to mention spittoons!!
Seriously, I will say that it was disgusting to go upstairs in buses in those days – a smog you could cut through and the smell and yellow/brown ceilings. Ugh! If I recall, on single-deck buses, the smokers were confined to the rear half of the bus. Smoking was endemic. I recall the clip of the ‘white horse’d’ policeman incident at Wembley in the twenties. A huge cloud of cigarette smoke rose from the crowd! Amazing.

Chris Hebbron


03/02/12 – 15:22

A bit off-topic, but following on from Chris H, I heard a tale of a certain paint shop foreman at Eastleigh railway works, who was given a new paint specification for Southern suburban trains, requiring white ceilings. Foreman was a bit of a curmudgeon, and said they’d had cream for years, and as far as he was concerned they would have cream until he retired. After a while Southern Region complained, and asked why they weren’t getting their white ceilings. Said curmudgeon was called before the production manager to explain himself. “There’s no point in painting the ceilings white,” he said. “After a fortnight they turn cream anyway with the cigarette smoke.” “So,” replied the production manager, “You, in your infinite wisdom, decided they should have built-in smoke!”

Stephen Ford


04/02/12 – 05:31

It is possible although not evident in the photographs that there could have been a handrail running horizontally along the lower deck at the top edge of the sunken gangway. It wasn’t just standees that needed something to hang on to, don’t forget the poor conductor too! Each time I look at the pictures, I can’t help but make a comparison with South Yorkshire’s TWY 8 which was re-bodied around the same time and had an identical shell but with platform doors and superior seats. Two notable firsts for me last year were travelling on it and meeting Chris Y on the same day!

Chris Barker


04/02/12 – 08:48

Lucky you, Chris B. I had the privilege of meeting Chris Y last year at Dunsfold – but the riding opportunities were very poor. Hope the return to Wisley improves that this year – but I gather there is no link with the (new) museum!

David Oldfield


29/03/12 – 08:23

In an earlier post Chris B mentioned that he thought that Wrays may not have had any covered accommodation at their site. I can recollect that from the late 1940’s until the 1960’s when I left Barnsley they had a garage on the left hand side at the bottom of Lord Street which could hold two vehicles side by side. Whether the roof was high enough to hold double deckers in the garage I am afraid I cannot remember but I think that it did. I think they also garaged their coal lorry there.

David Galley


29/03/12 – 17:54

Chris Hebbron jokingly refers to the use of spittoons on northern deckers. Interestingly many companies in the West Riding had notices on the upper deck forbidding spitting. Many of the Norths industries such as mining and textiles caused long term lung damage and TB was still an ever present in the thirties.

Chris Hough


16/01/13 – 13:44

YWT 572
Copyright Ian Lynas

Sorry to be a bit late with this contribution but I’ve only just found this website and what a great site it is. So many memories that I cant concentrate on work.
However, the interior views of YWT 572 were superb so my photo of the outside is a case of having a really bad camera (an Italian-made Bencini.) Italians are good at most things but cameras was not one of them.
This shot was taken in 1967 on an expedition with (I think) the late Jim Pass and Glyn Weigh from Oldham to Wakefield and was taken in South Elmsall (Emsull to the locals) on a trip that opened our eyes to the likes of South Yorkshire Motors, United Services and Ideal (Wray of Hoyle Mill and Taylor of Cudworth). I was told that YWT had a Lydney body but as it was built in 1959 as a rebody of a Leyland Tiger PS1, maybe it had a Lydney body in its first life but Lydney went out of business in the early 1950’s. I think YWT 572 under its previous guise had a Wilkes & Meade body but stand corrected if not.

Ian Lynas


16/01/13 – 14:47

Nice to see the outside of the bus. I would imagine that the white flash on the front was a belated and modest attempt at 1930’s streamlining!

Chris Hebbron


16/01/13 – 15:24

It’s got an interesting set of headlight/fog lights

Andrew Beever


16/01/13 – 16:36

Yes, I had one of those Bencini things, too Ian, a Comet S. In fact, as a collector of old cameras, I have one now, plus a couple of the bigger Koroll. I agree entirely with your assessment of them. They were mediocre both mechanically and optically. As for the array of head and foglights, this reminds us that fogs back in those days really were pea soupers.

Roger Cox


16/01/13 – 16:39

YWT 572_2

When Robert sent me the interior shots he also sent me a scan of a photocopy of a shot of YWT 572 when it was just leaving Roe, it wasn’t very good but with a touch of manipulation you can see the original headlight/foglight arrangement.

Peter


17/01/13 – 14:44

I see that Chris Barker has said above that he did not think that any of Taylor’s vehicles passed to Wray, but later stated that YWT 572 actually did. It is my own recollection that most of the Taylor vehicles did indeed pass to Wray (despite the fact that Taylor didn’t actually sell out to Wray, of course), and that Wray finished up with more ex-Taylor vehicles than the residue of their own existing stock. If, as is inferred above, the Taylor fleet initially passed with the business to Yorkshire Traction, the implication is that the vehicles were then passed on to Wray. The relationship between Ideal and Yorkshire Traction seems to have been easy-going, to say the least – on at least two occasions YTC vehicles passed to Ideal, which then proceeded to continue to run them in YTC colours.
The Huddersfield Passenger Transport Group website to which Chris refers actually has an entire page of photos of Ideal vehicles, and it can be found here www.jsh1949.co.uk/ The pics are of variable quality, however, and the one of YWT 572 is only average.

David Call


19/03/14 – 07:42

YWT 572 did indeed pass to Wrays along with tiger cub TWX963 both used by them TWX later passed Phipipson Goldthorpe for use on its Thurnscoe – Sheffield service

Garry


03/07/14 – 07:20

It would seem that the Ideal service from Barnsley to Pontefract began in 1923 and that in the early 1930s there were five operators in the partnership:-
Taylor of Cudworth, Wray of Hoyle Mill, Lancashire & Yorkshire Motors Ltd, Hartley and Wilson (these three based at Shafton).
Lancs & Yorks acquired the Hartley and Wilson shares and was itself taken over by Yorkshire Traction in 1934. I assume Tracky’s Shafton depot was inherited from them.

Geoff Kerr


04/11/14 – 06:37

I lived in Upton, near Pontefract from 1940-1985. I regularly travelled on the Ideal buses, either to Barnsley or to Pontefract. I recall one particularly snowy winters eve, probably 1958/59, when the bus was having a problem negotiating the steep hill out of South Elmsall. Passengers were asked if they would mind alighting and giving a helpful push to get the bus to the top. Several of us young men did so and the bus made it. At the top of the hill we got back on and continued our journey.

Albert Jones


25/11/17 – 08:14

I really love to see interior views of vehilces from this period. Interesting how the upperdeck lowbridge layout has pairs of doube seats rather than the four abreast single type. I like the "cable" pattern moquette as used by York Pullman

Tony J Griffin


15/01/19 – 06:52

I can remember back in the 1950s an outing that had 2 busses.
One was a low bridge type and the other a normal one.
Unfortunately, there was a low bridge about a mile down the road and the driver of the standard bus had forgotten that it wasn’t a low bus.
It pealed about 10ft of the roof off like a sardine can.
Fortunately, no one was injured.

David M


15/01/19 – 08:51

I’d like to add to a couple of points above, both coincidentally contained in Chris Barker’s posts. First of all the PS1 which was rebodied for Wray reappeared as KHE 526 rather than KHE 528.
Earlier Chris B had commented that he didn’t think that Wray had ever purchased a new vehicle. In fact ‘Bus Lists On The Web’ credits Wray as having had three vehicles new, only one fewer than Taylor. The three were:
AHE 110 Albion CX19/Pickering B34F, new 1945 (later to Carmichael of Glenboig)
AHE 987 Leyland Tiger PS1/Wilks & Meade C33F, new 1947 – this was the one later rebodied as KHE 526
DHE 40 Leyland Tiger PS1/Cawood B35F, new 1950
Note the correct spelling of Wilks & Meade.
Taylor’s ‘new’ vehicles are probably more memorable since they mostly dated from 1952-57 and therefore lasted well into the ‘enthusiast’ era.

David Call


16/01/19 – 07:23

Just a few additional thoughts. As Chris Hebbron commented, the white flash on the front of YWT572 was clearly a late addition, since it obviously wasn’t delivered like that. In fact, it is almost certainly a consequence of the arrival of CCK668, the ex-Ribble/Delaine Brush-bodied Leyland PD2, which also features on this site, and which didn’t come to Taylor’s until 1966. Do you think that the white flash was an attempt by Taylor’s to set their own vehicles apart from those of Wray’s? Certainly, there seems to be evidence that the relationship between Taylor’s and Wray’s wasn’t what it might have been. YWT572 and CCK668 may have been the only dds in use with Taylor’s at the time, since, unlike Wray’s, they did make significant use of saloons.
Because Bus Lists On The Web quotes Taylor’s as having received four vehicles new and Wray’s only three doesn’t mean that they were actually the only new vehicles, in fact I’m aware that both operators received new vehicles in the 1930s. An additional vehicle for Taylor’s is actually listed, but it’s credited to ‘Taylor’, rather than ‘Taylor, Cudworth’ so you wouldn’t find it unless you were to know what you were looking for.
Chris Y, I don’t think that the Traffic Commissioners had any say in whether or not a rebuilt vehicle received a new registration, it was down to the registration authority, and the latter did have varying standards.
The link I gave in 2013 to the ‘Ideal’ page on the HPTG website doesn’t now seem to work, so here’s a new one. www.jsh1949.co.uk/IDEAL
David M, are you prepared to say which operator was involved in the low bridge incident you mentioned? It clearly wasn’t Taylor’s or Wray’s, since neither operated highbridge vehicles.

David Call


YWT 572_2 Vehicle reminder shot for this posting


21/11/20 – 07:01

I have found H Wray jointly operating the 46 Pontefract – Barnsley service with Yorkshire Traction in the 1969 tracky timetable. You can see the joint timetable here – https://timetableworld.com/

Ken


 

Quick links to the  -  Comments Page  -  Contact Page  -  Home Page

 


 

Foden Works – Foden PVRF6 – OLG 855

Foden Works - Foden PVRF6 - OLG 855

Foden Works - Foden PVRF6 - OLG 855 - Full Front

Foden Works
1951
Foden PVRF6
Plaxton C??C

These excellent shots were contributed by Andrew Charles who took them in 2005 the vehicle was restored by its present owner Nick Helliker. This particular vehicle was built for the Foden Works Brass Band who used it to travel to all their concerts until 1979 when it was replaced by another Foden vehicle. It was then laid up at the Foden factory until it was bought by an enthusiast who stored it under cover until the present owner bought it and did a full restoration to the standard you see above.
Fodens rear engine layout was way ahead of its time in 1951 as most other manufactories had just nicely switched over to underfloor engines and would stay that way for quite awhile to come. In fact Andrews comment that accompanied the shots read:-

“With it’s rear mounted two stroke engine this configuration when viewed now from sixty years on has become the norm – indeed Volvo have just delivered the last underfloor engined coach – a B12B – to Pulhams of Bourton on the Water, all future production will be rear engined.” (09/10)

The engine fitted to the above was Fodens own 4·0 litre two stroke diesel engine although there was the option to have a 8·4 litre Gardner 6LW in which case the model code would be PVRG6. I think there would have been a noticeable difference in performance as the Gardner is twice the size of the Foden engine, unless being a two stroke made a difference in which case why did it never catch on with other engine manufactories. The body for the above was built in Scarborough by Plaxton and was based around their Venturer model. I am rather curious to know what the circular grill in the roof above  ‘Foden Coach’ is, a large air horn perhaps.
Oh does anyone know what the seating capacity is?

Photograph contributed by Andrew Charles


Lovely pictures of a fine vehicle. Direct comparison of the engine capacities (4.1-litre Foden versus 8.4-litre Gardner) is, as Andrew suggests, complicated by the fact that in the two-stroke engine each cylinder delivers power at every revolution—not every other revolution as in the four-stroke—and so should develop double the torque. You would therefore reasonably expect that with air delivered to the cylinders at atmospheric pressure a 4.1-litre 2-stroke would develop torque equivalent to that of an 8.2-litre 4-stroke, but in practice inlet air pressure has to be well above atmospheric in order to scavenge the exhaust AND fill the cylinder with a clean charge of new air all in one go, so a blower has to be provided. Whether this blower is seen as a mere scavenger or as a supercharger depends on the amount of excess air it provides.
On p98 of the 1953 edition of Commercial Motor’s "The British Commercial Vehicle Industry" the Gardner 6LW as fitted to Foden passenger vehicles is shown as developing 358 lb/ft torque at 1,300 rpm and the Foden 2-stroke engine as giving 350 lb/ft at 1,500rpm.
Gardner maximum power is 112 bhp at 1,700rpm against the Foden’s 126 bhp at 2,000 rpm. Not much difference in on-paper torque, then, but in real life you had to keep the Foden engine spinning, as low-speed torque fell off alarmingly. Hence the need for the 12-speed gearboxes used for example in those wonderful howling Hoveringham gravel lorries. I’ve never driven a Foden of any kind, but I had a day in a 3-cylinder 2-stroke Commer coach belonging to Spiers of Henley-on-Thames which really NEEDED its 2-speed axle to allow you to keep the engine whirring within it optimum range. My guess is that the Foden 2-stroke didn’t catch on with PSV operators because of a) exhaust noise, b) reasonable but not wonderful fuel consumption, c) maintenance costs and d) inability to lug at low revs.
Incidentally, Foden later added a turbocharger and planned a 7-cylinder version. Does anyone know what became of it?

Ian Thompson


Memories, memories: this site is therapy. Do I remember that the Foden engine sounded like one of those old dumpers? Presumably the idea was to keep the weight down at the back.
I’d say that the grille at the front was a vent- there don’t seem to be many others: it probably pushed the tubas ciggie smoke along a bit….
Lovely looking coach for its time, though.

Joe


My late father had the opportunity to drive a wide selection of vehicles during his war service with the army and always maintained that the very best lorries were the Fodens. They certainly seemed to uphold this reputation right up to the end – including the small foray into buses – producing vehicles of a very high quality. Surprising then that they did not make bigger inroads into buses than they did – but their niche market of specialist trucks was probably more profitable and time consuming.
The Plaxton Centenary book simply describes the grille as an air intake. For engine, passenger or tuba player it does not say.

David Oldfield


I think the reason Foden didn’t make greater inroads into the bus market was the same as for the ill-fated Daimler CD650 – Fodens were rather complicated and probably rather expensive. Most transport managers of those days were pragmatic and conservative, preferring something familiar that was known to be good enough rather than something unknown that might just possibly be better.
As for the two-stroke engine, Ian has explained it perfectly. The reason that torque fell off alarmingly at low revs was that the blower couldn’t keep up, and so alternate firing strokes would become weakened as the engine tended towards a four-stroke cycle. I owned the ex Samuel Ledgard two-stroke Foden coach ONW 2 (front-engined) for a short while. My impression was that it was smooth, powerful and effective as a coach, but would have been hopeless for bus work. It also tended to stall when manoeuvring, as the torque would suddenly be halved by the four-stroke effect if the revs got too low. More recently I have travelled in the back of Roger Burdett’s rear-engined two-stroke, and noticed a distinct chugging sensation as it pulled out of roundabouts for the same reason, since with a wide-ratio gearbox it isn’t easy to keep the revs up.

Peter Williamson


Peter I never drove ONW 2 as I was at Otley and Ilkley Depots, but I have the most vivid memories of the stretch of the A64 dual carriageway at Whitwell. The road has a high summit and a deep trough at both ends, and many’s the time ONW 2 could be seen in the offside lane overtaking virtually everything in sight. Once in full flight that fine machine could really swallow up the miles but, as I’m of limited technical knowledge, I’ve found your explanations of the two stroke limitations most fascinating.

Chris Youhill


The above Foden was purchased by Ken Batsford from Fodens and was kept safe until purchased by present owner. I have driven many Foden trucks and with regards the Gardner vs the stroker scenario, leaving Millwall with 21 ton of timber on board me in a s36/Gardner my mate in a s36mk7 stroker on Archway Rd climbing north towards Mill Hill/M1 he would be 2 gears lower than me but pulling away from me. Once on the M1 he would leave me for dead his top speed about 65/70 mine about 50/55. When I drove a 2 stroke you had to wind it up in every gear and note the speed you shifted gears at because that’s the speed you changed down at to keep the thing pulling hard, lose the revs and you were knackered. Driving the 12 speed you started off in 2 low range up to 4 low, up to 2 direct and then 2 overdrive 3 direct and so on. Fodens were cold and noisy or hot and noisy depending on the weather but good trucks, 2 strokes suffered with cooling problems and often scrapped cylinder heads (separate head per cylinder)

Chainmaker


Ah the 2 stroke Foden. My short stint as a driver for Transglobe (B’ham) brings back the memory of one of my nosier ‘steeds’ – and having to take it to the Foden works (Sandbach) for diesel pump adjustments. I think it had a Duple body.

Nigel Edwards


Engine aside, perhaps a major reason the Foden PVR was unsuccessful was that it was fitted with Lockheed continuous flow hydraulic servo braking. Other manufacturers also tried this (Daimler, Dennis) and would be buyers stayed away in droves. It was not that brakes were particularly poor (though in the case of the earlier Fodens, if the engine stalls than braking is reduced to practically nil) but sheer complication of the system and potential maintenance problems were enough to keep people away. The only bus that really saw success with a system like this was the Routemaster which took the might of London Transport’s engineering development to take the bugs out of the design.
I am, incidentally, the current owner of another Foden PVR coach, VRF 372, currently in restoration.

Nick Webster


Chris Youhill’s comments about ONW 2 overtaking nearly everything in sight reminded me of a report from a Commercial Motor correspondent, Alfred Woolf, who hitched a ride on Salopia’s HUJ 996, one of their rear engined Observation coaches, on its way to the Nice Coach Rally. Covering 800 miles in three days on roads of dubious quality, the coach ‘left most other public service vehicles behind, even those with more powerful motors’ and ‘provided that the engine speed is kept up, few vehicles can climb as well as the Foden’. On some stretches of prime Belgian pave, flat in nature, speeds of 60 m.p.h. were seen – and maintained for many a mile. The coach took the Grand Prix du Confort et de l’Elegance award – Whitson’s fifth such award! Another rear-engined Foden, OLG 968, was taken by Fodens on an Alpine Tour to test its suitability for Continental touring. Admittedly driven hard, to assess its capabilities, the coach averaged 30.2 m.p.h. and 10.8 m.p.g. over a total distance of 2,850 miles. This included scaling no fewer than five high Alpine passes, most of which were loose surface roads! I have heard an apocryphal tale that the coach was clocked by one German driver in excess of 80 m.p.h. – downhill and out of gear! Average speeds on the German autobahns were over 50 m.p.h. and even the long run from Strasbourg to Paris (302 miles) on standard main roads was completed at an average speed of 36.4 m.p.h. Yes, the two-stroke engined coaches were fliers, but you had to keep the revs up to get the best out of them.

Peter Tulloch


13/05/11 – 06:36

I think that must be a pic of the great Fodens bus that my father talked a lot about. He has fond memories of his days at Fodens Works at Sandbach. He was there for six years in the sixties then came home to run the family business of eight wheel Fodens. I have heard many a funny story involving that machine. Does Billy Harrison ring a bell to anyone?

Lee Harrison


21/01/16 – 15:33

I think that as well as a higher purchase price and the complication of the braking system, another problem with Foden PSVs particularly in the coach application is that of resale value, here the two stroke was particularly likely to depreciate heavily, at least you could take a 6LW out and use it in about 60% of other heavyweight buses and coaches of the same era.

Stephen Allcroft


30/08/19 – 10:01

I have really enjoyed being educated again at the age of 66, on the principles of two stoke engines. In 1961 when at school I can vividly remember the heavy bulk sugar lorries of Tate and Lyle in dark blue livery heaving and struggling to re-start from traffic lights on the old A11 London to Cambridge road. The exhaust note was unbelievable and with high revs and just poured out hot shimmering heat onto my bare legs, as I only wore shorts then for school. It always surprised me that the hot exhaust gases were even directed by design towards pedestrians on the nearside pavements! – such memories

Paul Tanner


01/09/19 – 06:09

Always interesting to comment on Fodens. I have travelled around 1500 miles in mine this year so it was great to look back over the comments and think how it had performed. Mine will do 60mph (twice the 1951 speed limit for coaches) but is really comfortable bowling along at around 50mph. Fuel consumption has been between 10 and 11 mpg as compared to 14mpg for my Gardners. The brakes whilst competent do not have accumulators so engine stopping means no brakes at all-can be scary. It is a pig to drive with the gearbox being transverse behind the rear axle meaning timing is really critical to clean changes. Anyone who has ridden with me this year will have seen one trip all clean next trip hit and miss. PW back in the dialogue talks about chugging coming out of roundabouts and he is totally correct. First being a crawler is not much use and wide gaps mean I have been caught out in the wrong gear more than once. Ironically it is better to be slower in roundabouts and use second rather than third. My style tends to be I clatter through roundabouts so it does require me to alter driving style. Switching from Gardner to Foden 2 stroke say a week apart means a totally different driving style. I understand the 12 speed box is essentially the same as mine just with a 3 way splitter.Having said that I love it but need a couple of extra hours sleep afterwards. It is running at Delaine Running Day Sept 28 and then resting until 2021.

Roger Burdett


13/10/21 – 03:30

OLG 855_3

While having an hour of browsing reminiscence, I came across this photo of the Foden Works Band’s coach. I took it on a damp day at Blackpool on August 22, 1976. The livery has been reversed in the top photo of 2005 and the fog lights changed. The GB sticker and row of city stickers along the bottom of the windscreen look like trophies of a continental concert tour.

Geoff Pullin


13/06/22 – 06:25

The Mark 7 Six cylinder engine was the last model built. It had higher pressure fuel injectors compared to the earlier Mark 6 with blue caps instead of black in order to distinguish them. I worked at Foden’s in Elworth in the late ‘Sixties and spent some time building the engines. At that time, Gardner LW’s and LX’s were being rebuilt there. The crankshaft bearings on the LW’s had to be scraped in and, as an apprentice, you only touched the face of the bearings once with your fingers. A blow at the side of the head from the fitter put paid to further attempts. Apprentices learnt quickly in those days. In the experimental department, one test run they used was up Shap Fell, the apprentice logging the figures from the multitude of analogue gauges which, as I recall, were built into a board. Regarding Billy Harrison (Lee Harrison) I don’t recall Billy but I do remember a Paul Harrison. He would have been in his late teens in 1969.

Daniel Preston


14/06/22 – 06:12

OLG 855_4

Thought you might like to see a recent photo including this coach when it appeared at the Didcot Transport Rally.

John Lomas


 

Quick links to the  -  Comments Page  -  Contact Page  -  Home Page

 


 

Huddersfield Corporation – Daimler CVG6 – DCX 114B – 114

Huddersfield Corporation 114 Daimler CVG6 front view Huddersfield Corporation 114 Daimler CVG6 rear view

Huddersfield Corporation
1964
Daimler CVG6-LX30
Roe H39/31F

This particular vehicle has appeared on this site before, but a comment came in from Stephen Ford requesting any rear or internal shots. So I thought I would oblige, no internal shot I’m afraid but it’s not a bad rear end. I notice on this particular vehicle there is no destination blinds at the rear I do not think it was as easy to have them on front entrance vehicles. I know they had rear destination blinds on the rear entrance Regent IIIs I used for school, the number of times I saw the 63 tootling merrily up the road resulting in me having a one mile walk home or wait an hour for the next one.
If you have any rear or internal shots please feel free to contribute them to the site for everyone else to see.


This bus ..114 was a Huddersfield Joint Omnibus Committee bus it was never fitted with rear number blinds … the Joint omnibus committee vehicles at the time were allowed to carry adverts .. and the space was available for advertisers .
The similar buses that were owned purely by the Corporation had rear number blinds fitted up until 1966.
The Corporation at the time did not allow any advertisements on the outside of its vehicles.

Colin


In my West Yorkshire gallery this difference is illustrated by a couple of consecutive rear end photos of (3202 and 3203) in the Holme Valley collection. See here

David Beilby


Interesting shots of the Roe rear ends David. I note that the lower rear panels from the axle back have been shortened to prevent them ‘grounding’ when negotiating junctions at the bottom of very steep hills. Bradford C T carried out this modification to the rear overhang of many of its MCW-bodied AEC Regent Vs for the same reason, with the rear chassis extensions being similarly visible. On the subject of rear ends, does anyone else wonder why some coachbuilders fitted (and some operators specified) such dated features as split upper deck emergency windows, on what were otherwise quite modern-looking front entrance buses? Even the ‘balloon roof’ Alexander bodies mounted on Atlantean and Fleetline chassis could be had with them, despite having very modern curved screens on both decks at the front!

Brendan Smith


 

Quick links to the  -  Comments Page  -  Contact Page  -  Home Page

 


 

All rights to the design and layout of this website are reserved     

Old Bus Photos from Saturday 25th April 2009 to Thursday 4th January 2024