Old Bus Photos

Ideal Service – Leyland Titan – CCK 668 – 16

Ideal Service - Leyland Titan - CCK 668 - 16
Copyright Unknown

Ideal Service (R Taylor & Sons)
1949
Leyland Titan PD2/3
Brush L27/26R

New to Ribble Motor Services (No 2691) in 1949 passed to Delaine Bourne in 1961 as their (No 54) where it served 5 years when it then passed to R Taylor & Sons Cudworth in February 1966 (No 16) part of the Ideal Service When Taylors sold out to Yorkshire Traction in 1967 this vehicle passed to H Wray & Sons of Hoyle Mill Barnsley and remained in service until 1969.
Photographed outside Taylor’s garage at Cudworth.

Photograph and Copy contributed by Brian Lunn


26/09/17 – 06:45

Twenty years service from one of these vehicles who’s Brush bodies were said to be of questionable durability was a good innings.
Delaine’s beautiful livery must have inspired Taylors to replicate the V arrangement on the upper deck front panel and the application of the IDEAL name on the (illuminated?) glass panel is a nice touch. The large fleetname on the side is just visible and the whole thing looks very smart indeed, a worthy transformation from blue to red!
I can’t help thinking that H Wray & Sons might not have gone to the same trouble!

Chris Barker


26/09/17 – 14:23

Judging by the rubber window mounts I would guess this vehicle’s bodywork was rebuilt/refurbished somewhere along the way. In 1949 except for ECW this type of window mounting was rare. I seem to recall hearing or reading that at this time ECW had this type of window mounting patented. I am sure someone will comment.

Philip Halstead


27/09/17 – 06:22

Pictures of this bus in Delaine’s ownership are seen here:- //www.delaineheritagetrust.org/54.html The windows had already acquired the external flush rubber glazing at that time, so a body refurbishment took place either under Delaine or earlier. Full details about Delaine, including a historic fleet list, may be found on this web page:- //www.delainebuses.com/fleet.html

Roger Cox


 

Quick links to the  -  Comments Page  -  Contact Page  -  Home Page

 


 

Bradford Corporation – Leyland Panther – NAK 512H – 512

NAK 512H

Bradford Corporation Transport
1969
Leyland Panther PSUR1A/1
Marshall B45D

For 1969, Bradford Corporation ordered ten chassis of the rear horizontal engine variety, its first new single deckers since a couple of AEC Reliances in 1958. The ten new chassis were split between AEC’s Swift and Leyland’s Panther, but, since the chassis design of the two types was virtually identical apart from the engine manufacture and the radiator position – at the rear on the AEC and at the front on the Leyland – the exercise was probably intended to ascertain which power unit was best suited to the challenging Bradford terrain. All ten were equipped with Marshall B45D bodies. Seen above in April 1970 is the last of the batch, No. 512, NAK 512H which was delivered in December 1969. In the event, no further single deckers were to be bought by Bradford before the infliction upon all the West Yorkshire municipalities from 1st April 1974 of the all embracing WYPTE. In this new conglomeration, the five Bradford Panthers were the only examples of their type, and the PTE Director of Engineering, a certain Geoffrey Hilditch, soon sold them all to Chesterfield. A picture of one in service in that town may be seen here (a very long page, but about halfway down – search for Chesterfield in the browser :- www.mikesbuspages.com/municipalbuses.htm
In his book Steel Wheels and Rubber Tyres, GGH says that pictures of the Bradford Panthers in original livery are hard to come by – he should have asked me.

Photograph and Copy contributed by Roger Cox


11/09/17 – 06:38

Nice pic!
Stuart Emmet Another story on these 10 was they were bought to start OMO; however double decker OMO was approved legally soon after they were ordered, so they were redundant as far as that went. They spent their time inventing conversions to single decker routes and seemed to settle on the 61 as shown – about a 25-minute journey across town from Undercliffe to St. Enochs that went for around 5 mins over roads in the Canterbury Ave area that were not used by other routes.Effectively a peak hour route every 10 min from 0700 to 0900 and 1600 to 1800 with a few journeys between 1200 & 1400 hours that required 6 buses for the 10-minute headway. The rest of time they seemed to rest/in-filled as spares.

Stuart Emmet


12/09/17 – 06:46

From 1969, BCT participated in White Rose Express service X33, Bradford – Sheffield, which entered its area at Birkenshaw. The other joint operators reluctantly agreed, even though Bradford’s entitlement was no more than one journey per week! In practice, as explained to me by the late Stanley King, Bradford saved up their mileage until they were able to operate a bus for a whole week, replacing a Yorkshire Woollen duty.
BCT had few single deckers and I believe these Panthers and the contemporary Swifts were used. Does anyone recall seeing a photo of a Bradford bus on X33, as I’ve never seen one.

Geoff Kerr


12/09/17 – 06:47

Just about everyone was caught with the change of legislation which allowed DD OMO. Sheffield certainly was – initially with purchase of the Swifts and subsequently with the change of Bristol order from REs to VRs.

David Oldfield


13/09/17 – 06:46

In the lovely book Colours of West Yorkshire the author states that these were ordered because agreement could not be reached with the Unions to operate OMO double deckers. I.e. The legislation already permitted it but not the Unions until agreement was reached later on.

Sam Caunt


14/09/17 – 07:04

The Bradford manager at the time was not in favour of one man buses These and the Swifts were also used on the express X72 which ran between Bradford and Leeds at peak hours.

Chris Hough


15/09/17 – 06:45

I recall someone (who I believe was very knowledgeable) telling me that as late as 1981/2 that Bradford area buses of West Yorkshire PTE were around 80% crew operated.

Dave Towers


16/09/17 – 06:47

The change in legislation to permit double deck OPO was in 1966, and I doubt that an order for vehicles to be delivered in 1969 had been placed before that date – i.e. the fact that D/D OPO was possible would have been known.
I like to see a clear and readable destination display, but in this case I suspect that a slightly smaller window would have fitted the lines of the vehicle rather better!

Nigel Frampton


17/09/17 – 06:55

Another story was that the unions rejected the DD legislation but SD would be OK It was also said on delivery of these SD’s unions OKed the use of DD OMO How far this any of this is fact or fiction seems lost in time.

Stuart Emmet


18/09/17 – 07:19

I started working at Bradford City Transport in the Traffic Office in October 1973. The story of OMO at BCT is intriguing. I cannot comment on the position of General Manager Edward Deakin in relation to OMO, although I could find out as Bob Tidswell his PA is still heal and hearty. I can say that Traffic Superintendent John Hill was not very enthusiastic about OMO, and from all accounts the T&GWU branch was not very keen, either. Around 1971 or 1972 the position of Asst. Traffic Superintendent became vacant and Brian Eastwood, who was Traffic Superintendent at Maidstone Corporation, was appointed to the post. Maidstone had undertaken extensive conversion to OMO and BCT felt that Brian’s experience in this regard would be extremely useful. Many years later Brian told me that when he arrived at Forster Square – BCT Head Office – there was little enthusiasm for OMO. Earlier this year I had lunch with Brian and he said that many of the new ideas that he tried to bring to Bradford fell on stony ground. Maidstone had a very large circle OMO sign on the front of their Atlanteans and Brian arranged for one of the signs to be sent to Bradford for evaluation. John Hill rejected the idea. Bob Tidswell once told me that Edward Deakin had a policy of splitting chassis orders between manufacturers – and thus having small batches – on the basis that if one chassis type developed a serious fault then the impact on the operational fleet would be minimised. Some of the single-deckers were allocated to Ludlam Steet and were used on the 272 service to Leeds, the 61 and sometimes other routes operated from the depot, such as Eccleshill, Fagley and Haworth Road. They were used on the White Rose service and at weekends for private hire work at weddings etc. When the PTE was formed John Hill became Metro Bradford District Manager and the position of District Traffic Officer was given to Bert Henry from Leeds City Transport who was very keen to expand OMO across the Bradford route network.

Kevin Hey


19/09/17 – 06:01

Still trying to get "facts" and the best come across so far, is from the JS King book. The following is a timeline summary:
1967
BCT ordered the Swifts and Panthers (503-512 ) to start OMO and had the unions OK 8 and 10/1969. The Swifts and Panthers arrived but went to work with conductors on 61, 83 and 27-29/32. Cannot find a reason why they were not used for OMO. These buses were also available for breakdown cover for the other operators on the joint with 7 other operators "White Rose" express to Sheffield; BCT having only one journey a week which they "banked" so they could then a bus operate all week.
Mr King notes the SD were already "white elephants", as by now DD OMO was acceptable, so seventy 33 foot DD were ordered, with union acceptance of OMO for these 2 door 33 foot vehicles.
8/1970
The DD start to arrive (401-470) but unions said no as are too long and the drivers’ view of exit door was insufficient. So OMO introduction postponed once again.
9/1971
SD work on the peak time only Leeds express (272) joint with Leeds CT who operated SD OMO, but BCT used conductors
31 Dec 1972
OMO finally starts using 30 foot DD (315 to 355) on routes 36-38 and 40-42 20 May 1973
OMO starts on joint working with Leeds on the 72 route
Footnote
This appears is a strange story, that however, shows the management/union environment at the time.

Stuart Emmet


19/09/17 – 06:02

Re Kevin Heys comments. There was a regular evening trip on service 46 to Buttershaw.
OMP operation commenced in Bradford with the conversion of the 72/78 services between Bradford and Leeds which were jointly operated with Leeds City Transport. This started in late May 1973. I cannot recall them being used on White Rose services during my time in Bradford in 1973.

Stephen Bloomfield


22/09/17 – 07:15

I suspect that when BCT ordered dual doorway buses the ‘agreement’ with the T&GWU was merely one of outline or agreement in principle to discuss the matter. It would appear that a detailed agreement with signatories was not secured until 1972. The initial conversions at the end of 1972 used single door Fleetlines, but evidently the T&GWU was prepared to allow two-door buses to be used on services to Leeds when these were converted in May 1973. The feeling I detected at Bradford was that neither management nor the T&GWU were keen to pursue OMO. Management believed that OMO made the service worse for passengers, while the T&GWU was against a reduction in potential members and staff – members – losing overtime.

Kevin Hey


21/11/17 – 08:30

Just a reminder that the 5 Panthers transferred to Calderdale in early PTE days. There was a serious blind spot problem with the blank front corners and all were modified with small corner windows. Memory fails me but I wonder if a serious/fatal accident blamed on lack of visibility occurred. I recall that these weren’t bad buses, hadn’t done a lot of mileage with Bradford.The biggest problem was (the lack of) pit length and accessibility with 36′ long buses in the Dock Shop at Skircoat Road. They were also a bit limited on allocation because of road/junction/camber problems on many routes. Someone out there will remind me how long they ran in Halifax prior to sale to Chesterfield where they put in a good number of years service.

Ian Wild


22/11/17 – 07:22

The first of the Bradford Panthers to arrive in Halifax was 2511 in October 1974, followed by 2508/10/12 in November and 2509 in December – all still in BCT blue and cream livery. They were allocated solely to the 5/6 West End Circular route, which required four vehicles during the daytime just going endlessly round and round, so presumably the fifth one was usually either parked up or ‘day in’ for maintenance. I don’t think the trade union would allow them to be used on any other route – I certainly don’t remember seeing them anywhere else.
Unfortunately one of them was involved in a fatal accident when operating a 6 (clockwise) journey and turning right from Heath Road into Free School Lane – just a couple of hundred yards from Skircoat Garage. They had very thick front corner pillars which caused a terrible blind spot for the driver. The bus had begun to take the right turn and was not cutting the corner when a young chap on a moped approached from the right and appeared to stop at the junction with the intention of going straight ahead after the bus had turned. However he must have decided to chance it and accelerated across the front of the bus, but due to the blind spot the driver couldn’t see him and a terrible accident ensued in which the lad was killed. The bus driver was shown to have been blameless.
The five were immediately taken off the road and, as Ian says, small (very small) windows were let into the pillars. My records only show that they were withdrawn during 1975, but that they passed to Chesterfield Corporation in the September. They ran them quite successfully until 1985/86 after which they saw even further service with CityBus in Manchester.

John Stringer


24/11/17 – 07:23

That sounded a terrible, tragic accident indeed for all concerned John, and it still amazes me that in this day and age just how many modern cars have quite serious blindspots, especially to the rear. West Yorkshire had a 1964 Bristol RELH6G express coach (ERG1/1001: AWR 401B) refurbished by Willowbrook in 1977, which included a new peaked front dome, Duple-type windscreen and revised front dash panel, grille and headlamps. On return to West Yorkshire, and before re-entry into service, the Duple screen was removed and the original ECW ‘wrap around’ version reinstated. This was not connected with night-time reflections as is often stated, but due to a serious blind spot either side of the windscreen. The Duple screen had curved sides, which on a Duple (or Plaxton) body would not have been a problem, as the body pillars/sides were also curved and therefore matched. The ECW body had straight pillars/sides, but the curved Duple screen was matched up to the front pillars using an infill panel at either side, which flared out towards the top. The local ‘Man from the Ministry’ would not pass the vehicle as he felt the blind spots were a serious hazard, hence the change back to original spec. We’ll never know, but the thoroughness of that Ministry Inspector may well have prevented a serious accident at some point, and even saved a life, for which we should be very thankful.

Brendan Smith


29/12/17 – 07:47

The reference to the Panthers being used on the White Rose appeared in a recent book- though I couldn’t find the reference when I looked for it, inevitably. I moved to Sheffield in 1969 and used the X33 regularly but never saw or heard of Bradford actually working on the White Rose; more significantly no record of such a working ever appeared in local enthusiast publications of the time and I never heard fellow enthusiasts mention it.’Joint operation in South Yorkshire’, published by the Omnibus Society in 1974, is also silent on the issue, despite mentioning that, for instance, Ribble provided duplicates on Yorkshire Traction’s X19 (Manchester-Barnsley). It would be intersting if anyone can produce chapter and verse on Bradford’s involvement.

Phil Drake


29/12/17 – 09:48

There was mention somewhere to the effect that the Bradford share, based on the miles of the route in Bradford, was small, therefore Bradford saved up the miles which meant something strange like one bus every x weeks or similar. Will try and find the reference for you. Additionally, Brasford was able to provide breakdown cover for any buses having issues.

Stuart Emmett


30/12/17 – 08:46

Extracts from J S King (1995) Bradford Corporation Motorbuses pages 99 and 100. John King (RIP) is the acknowledged expert on all matters Bradford (trams, trolleys and buses).
Mexborough & Swinton had proposed a network of routes along the then new M1. A consortium of interested parties was formed with M&S, Sheffield JOC, Rotherham, YWD, YTC, WR and Hebble and a service from Sheffield to Bradford via Dewsbury was agreed.
On hearing of this Bradford applied and got consent but as the route in Bradford was less than 10% of the whole giving one journey a week, Bradford decided to accumulated mileage until there had enough for one bus for one week when they took over a YWD duty.
Sheffield, Barnsley and Mexborough were to now appear on all future Bradford buses, meanwhile, 505 to 512 were made available and were occasionally used.
A trial run by Bradford took place on the 14th October 1969 and service started four days later.

Stuart Emmett


08/01/18 – 07:21

Sorry about the delayed reply, but thanks to John Stringer for details of the fatal accident with one of the Panthers whilst in Halifax. It makes you wonder how they ever got through initial certification, I’m almost certain the blind spot would never have been accepted by the Yorkshire TA Certifying Officers. I recall a couple of Halifax Leopard/Weymann buses being ‘overhauled’ as an emergency measure by Willowbrook. They came back with new 6 year certificates (12/13 year old buses by this time) with far less work than we had to put in to obtain a grudging 5 years. This difference in standards in different Traffic Areas continued up to the day I retired!

Ian Wild


 

Quick links to the  -  Comments Page  -  Contact Page  -  Home Page

 


 

Ribble – Leyland Titan – RCK 920 – 1775

RCK 920

Ribble Motor Services
1962
Leyland Titan PD3/5
Metro-Cammell FH41/31F

In 1956 the UK maximum legal length for double deck buses was extended to 30 ft, and Leyland quickly responded with the PD3 chassis, essentially an elongated version of the PD2. Ribble ordered a fleet of 105 synchromesh gearbox PD3/4 machines distinguished by handsome Burlingham FH41/31F bodywork featuring a neatly designed full width front end. These entered service in 1958, but Ribble then tried its hand with the then very new and novel Leyland Atlantean design, taking 100 examples in 1959/60. All operators of the early Atlantean experienced a number of teething troubles, and Ribble, while continuing to favour the Atlantean for future orders, hedged its bets by partially returning to the more dependable PD3 for some of its 1961-63 deliveries. The bodywork was again FH41/31F, but this time of the aesthetically less appealing (to my eye, anyway) Orion style by Metro-Cammell . These later machines, which totalled 131 in number, were equipped with pneumocyclic gearboxes, making them type PD3/5. No.1775, RCK 920 was delivered in 1962 and operated in the Liverpool/Bootle and Carlisle localities until its withdrawal in 1981, when it was subsequently acquired for preservation. At some time in the years following, 1775’s pneumocyclic gearbox failed and was replaced by a synchromesh unit, but, when, in 2010, the vehicle passed into the hands of its current owners, the Ribble Vehicle Preservation Trust, the pneumocyclic box was repaired and refitted, bringing the bus back up to its original condition. In the picture above, 1775 is seen at the Wansford, Cambridgeshire, premises of the Nene Valley Railway on 8 July 2006 where I encountered it entirely unexpectedly.
A YouTube video of a ride on this bus may be found here:- at this link

Photograph and Copy contributed by Roger Cox


22/08/17 – 06:32

Although rather plain I always thought these were quite attractive vehicles. The proportions seem to sit right and the livery suits the lines of the bodywork very well. Dignified is the way I would sum it up which is more than can be said for the horrors seen on most modern vehicles.

Philip Halstead


22/08/17 – 06:33

The change away to a synchro box was done when owned by Gerald Boden (who owned a B1+Class 40). From my memory he chose to do it as it would have been cheaper to repair the semi auto.

Roger Burdett


23/08/17 – 06:17

The almost only one-coloured livery hardly favours the body shape, Philip. I can see an improvement in Southdown livery. Oops, it must be the sort-of Queen Mary shape that reminded me of that!

Chris Hebbron


25/08/17 – 06:52

I wondered if Roger Cox or Roger Burdett can shed any light on the original gearboxes (or their flywheels) that were at first originally fitted to these Ribble PD3’s (and for that matter the fully fronted Bolton PD3’s).
When new, at idle there was a most musical tinny mechanical sound that soon disappeared once power was applied, I think they had a mechanical flywheel then. Bolton and later Ribble soon changed them to the fluid flywheel, which I understand gave a better service life – but no music! Hope someone in the ‘know’ might be able to offer enlightenment.

Mike Norris


25/08/17 – 09:36

I believe you are referring to the centrifugal clutch which I suspect was intended to be more efficient than a fluid flywheel. I only had very limited experience of it on a Bolton bus and simply remember an awful racket when the bus was in idle, not something I would describe as music at all.

David Beilby


25/08/17 – 09:37

Cannot shed any light except to speculate it was a body vibration due to harmonics.
Maybe someone from Ribble Group can enlighten if the switch back to a stick box has re-introduced the sound

Roger Burdett


25/08/17 – 09:38

I think that "jingling noise" was symptomatic of a centrifugal clutch, which was an attempt to provide a degree of automatic change, but without the drag and therefore fuel consumption penalty of a fluid flywheel.However I could be wrong.

James Freeman


26/08/17 – 07:13

I’ve noticed in several posts reference to ‘synchromesh’ gearboxes (as above) but am I right in thinking that they were only synchromesh on third and fourth gears? On every Southdown Leopard and Queen Mary I drove that was the format but may have differed elsewhere?

Nick Turner


26/08/17 – 07:14

This page seems to confirm that these Titans were initially fitted with centrifugal clutches:- www.flickr.com/photos/ Several operators tried out the centrifugal coupling to improve fuel consumption – the fluid flywheel could never attain 100% drive efficiency – but transmission snatch and maintenance problems meant that the fluid flywheel reigned supreme until the arrival on the psv scene of the multi stage torque converter gearbox.

Roger Cox


26/08/17 – 07:14

The Wigan PD3’s which were pneumo-cyclic also made this noise. Wigan went back to manual gearboxes for their later PD2’s so perhaps there was some dissatisfaction with the semi-auto transmission.

Philip Halstead


27/08/17 – 07:01

I seem to recall there was another stage of development when centrifugal shoes were included in the fluid flywheel so that it locked up at a suitable speed. I can’t recall technical details of the Ribble/MCW PD3 but know they seemed to perform very well up to the bitter end of TMO in Merseyside.
PS> The Captcha code for this post is PD3A!

Geoff Pullin


27/08/17 – 07:02

The PD2 was initially supplied with the GB63 four speed gearbox that had synchromesh on second, third and top, bottom gear being simply constant mesh. Unfortunately the second gear synchro set up gave some trouble in that engagement was often strongly baulked. Geoffrey Hilditch records examples of the resistance to engagement being so severe that gear levers were snapped off by the over enthusiastic pressures being applied by desperate drivers. Leyland then offered the GB83 box in which the second gear synchromesh was eliminated, and this continued to be available after the second gear synchro problems of the CB63 box were sorted out. All the PD2/PD3 buses I drove in Halifax had synchro on second gear.

Roger Cox


29/08/17 – 06:38

For those who like classic liveries like this, there’s news from Arriva. Their new universal bus livery is a simple Bradford blue, it seems: not clear to me how many extra bits or brandings can be added or where, but others may have more intimate knowledge. It does look if all the fussy skirts and linings may have gone, but what about the odd flash? After First, this is a relief!

Joe


22/07/18 – 06:20

To confirm what has been discussed about the PD3’s with the semi-auto g/box the Fleet nos starting with 1700 were all fitted with the Centrifugal Clutch and the fleet nos starting with 1800 were all fitted with the Fluid Flywheel.
The Centrifugal Clutch used to rattle when the engine was on tickover as the toggles and pins were worn, as when they were new they used to whine until the clutch engaged.

Norman Johnstone


 

Quick links to the  -  Comments Page  -  Contact Page  -  Home Page

 


 

All rights to the design and layout of this website are reserved     

Old Bus Photos from Saturday 25th April 2009 to Wednesday 3rd January 2024