Old Bus Photos

PMT – Leyland Titan PD2/20 – 203 BEH – L679

PMT - Leyland Titan PD2/20 - 203 BEH - L679
Copyright Ian Wild

Potteries Motor Traction
1957
Leyland Titan PD2/20
Willowbrook L27/28R

This bus was new to Baxters of Hanley as their fleet number 11 in March 1957 and was acquired by PMT when they bought out the Baxter business in December 1958. It was somewhat different from the contemporary PMT purchased Leylands having a concealed radiator and rear entrance and by 1968 was one of only three double deckers in the fleet without platform doors. A similar but slightly older bus from the Baxter fleet became PMT L510 which was rebuilt with a MCW style top deck after an altercation with the notorious Glebe Street railway bridge adjacent to Stoke Station. L679 was allocated to Stoke Garage and is seen in Woodhouse Street outside its home depot on 10th October 1970. By this time it was normally only used for a morning and afternoon peak hour working on the Longton to Newcastle Estates group of services (numbers 98-103) where it was odd man out amongst the Atlanteans and Fleetlines. By the date of this photo was used in between peaks for driver training – note the slot for an L plate above the radiator grille. It became a permanent driver training vehicle in December 1972 and was withdrawn for disposal in 1976.

Photograph and Copy contributed by Ian Wild

A full list of Titan codes can be seen here.

———

06/04/11 – 05:00

Would I be correct in thinking that these ex Baxters vehicles were the only PD2’s ever bodied by Willowbrook in this style? By 1957, Willowbrook had changed their design for deckers to the more rounded style, as on the Barton PS1 rebuilds and several deliveries to that design actually pre-date the vehicle shown. I believe the very last one to this ‘old’ design was a Daimler CVG6 supplied to Blue Bus Services in 1960.

Chris Barker

———

08/04/11 – 05:00

Yes I did a bit of driver training in this vehicle but I must admit I liked my normal training bus better which was LEH 745 L337 NCME body.

Michael Crofts

———

28/04/11 – 06:36

I passed my PSV test in 1968 on L337, I preferred my training turns on L466 (now preserved) as it had a sliding cab door which I was able to leave open. I remember struggling with hill starts on Penkhull New Road!!
The Chief Instructor / Examiner was George Clews but I don’t remember the names of the other two Instructors. Rather unusually the Driving School reported to the Chief Engineer rather than the Traffic Manager.

Ian Wild

———

06/05/11 – 06:46

Hi ian, Yes my instructor was George Clews but my examiner was from the D.O.T he took me into a cul-de-sac by mistake and I had a devil of a job doing a shunt to turn around with 337. Yes those were the days on Penkhull bank….

Michael Crofts


 

Quick links to the  -  Comments Page  -  Contact Page  -  Home Page

 


 

Luton Corporation – Daimler COG5 – CNM 43 – 68

CNM 43_lr             Copyright John Barringer

Luton Corporation Transport
1938
Daimler COG5
Willowbrook L26/26R

Probably the only surviving picture of fleet number 68 registration CNM 43 chassis number 10337 taken just after withdrawal in 1952. Luton Corporation Transport purchased a fleet of Daimlers in the early 1930’s to replace the tramway system that had served the town for a number of years. I suppose the thinking was that ex tram drivers would be able to come to terms much easier with semi automatic pre-selector gearboxes and fluid flywheels than the crash gearboxes offered by other manufacturers. These were mated to Gardner 5LW engines which on the face of it seemed rather small to haul these machines up the steep inclines each side of Luton town. Many of these old Daimlers soldiered on into the 1950’s despite sketchy wartime servicing and the Luton bus garage receiving a direct hit from a Nazi bomb.
The low bridge Willowbrook coachwork had much character with the unusual feature of an upstairs with one gangway each side of a raised dais giving each bench seat only three places instead of the usual four. This meant that whichever side you sat downstairs you would still risk banging your head.
The drivers cabs were also a bit claustrophobic and had a small box section let into the roof to accommodate tall drivers.
For some reason the Gardner 5LW engines were much quieter in these compared to the Eastern National Bristol’s that also ran into Luton. Perhaps the fluid flywheel had a cushioning effect or maybe they had flexible engine mounts. In any case one characteristic of the Bristol’s was that each window would vibrate in turn as the engine revs gathered pace.
One notorious hill that tested these Daimlers to their limit was Crawley Green Hill to the east of Luton. I worked for Vauxhall Motors in the 1950’s and would sometimes wait at the top of this hill to catch a bus to Stopsley. The water supply in Luton contains a high proportion of chalk and no doubt this was used to top up their radiators. This resulted in a well laden bus boiling at about halfway up this hill and the driver having to switch on his wipers to clear the screen of condensed water. You will notice that number 68 has the engine side panel leaning against the wing in the time honoured way to give an extra cooling effect. Despite this the drivers cab would be writhed in steam at the top and a short wait would be required to cool them down.
At tick over and in neutral they would emit a ‘wind in the willows’ whine that would stop abruptly as first gear was engaged. As the driver put his foot down the bus would shake slightly as the fluid drive began to bite and to the sound of creaking coachwork the bus would slowly move forward like a dowager duchess perambulating at a garden party.
Happy days!

Photograph and Copy contributed by John Barringer

A full list of Daimler codes can be seen here.

Bus tickets issued by this operator can be viewed here.


17/02/11 – 08:59

I love John’s wonderful literary description of the characteristics of these most interesting vehicles – a batch which, incidentally, I’ve never encountered before. While three window upper saloon windscreens were fairly common before WW2, this particular arrangement is most unusual and has the suggestion of the bay windows in many houses. The phenomenon of "each window vibrating in turn" was also frequently evident in the Leyland TS and TD diesel models, particularly when setting off in second gear. Sadly there are few, if any, such controlled acoustic delights in today’s "sophisticated" offerings.

Chris Youhill


17/02/11 – 09:49

Come on, Chris. Yorkshire folk tell it as it is.
…..in today’s characterless sewing machines!

David Oldfield


18/02/11 – 07:27

John Barringer Great to see these old photos surfacing even when not my ‘location’ I must explore more of the website.
Thanks for this one.

Ian Gibbs


18/02/11 – 07:29

A very evocative description that takes me back, too! Luton dabbled with Willowbrook bodywork for much of the 1930’s, but these were the last of the breed. They all went between 1950 and 1954. The double gangway certainly restricted the seating capacity, the full code being L26/26R!
I’d say that these buses were about the last of the bay-windowed breed, too, although Dublin were still ordering such fronted buses in the late 1940’s, if not a little later. Personally, I rather liked this style of front.
The Bovril adverts are ones I’ve never seen before, and don’t make outrageous claims, either!

Chris Hebbron


18/02/11 – 07:30

I’m very pleased to see this as I was about to post a question regarding pre-war Willowbrook bodies with the upper deck arrangement which John describes. In an article about Mansfield Independents in Buses Extra in 1985, Roy Marshall recalls that Ebor had some of these, with a continuous sunken gangway which allowed the conductor to work round the top deck in a circle. Now, try as I might, I just cannot imagine how this was configured, how would it have been continued under the front canopy or over the rear platform? Do any plans or diagrams or even photos exist? In the same article, Mr Marshall mentions that Trumans of Shirebrook bought a Guy Arab in 1946 and fitted it with a 1931 Park Royal lowbridge body on which the sunken gangway had been built up to normal height forward of the front bulkhead to meet postwar certification regulations, an accompanying photo clearly shows the area above the cab and canopy screened off by a series of handrails. My point is that on every lowbridge vehicle I’ve ever been on, the sunken gangway stops at the front bulkhead (i.e. back of the cab). Even if pre-war construction and use regulations allowed different, how would the driver get into the cab and surely driving would have been well nigh impossible! Did any other coachbuilders have a go at this layout or was it unique to Willowbrook?

Chris Barker


18/02/11 – 10:42

Interesting that 1937 Thames Valley Leyland double deckers had a 3-panel "bay window" upstairs at the front, but were bodied by Brush, years before any business connection with Willowbrook. The small outer windows of the Brush version were less angled than those on the Luton deckers. The TV buses had a conventional single sunken gangway, but I’m fascinated to see that Willowbrook used a double gangway as late as ’37!
Chris Barker’s question exactly echoes one that’s been niggling me for years: how did you get from one gangway to the other??? A cross-gangway immediately behind the front bulkhead (front passengers downstairs Mind Your Heads!) would make sense, though it would entail a long circular tour for anyone nearside rear, but the view of seat-tops in the few surviving photos of double-gangway double deckers suggests otherwise. Another possibility might be to drop the last eighteen inches of the downstairs gangway, just aft of the axle, to platform level, so as to afford headroom for a cross-gangway upstairs over the platform, immediately forward of the stairs. This way everyone not sitting would get their allotted 5’10 1/2" of headroom, though tall folk would need to be careful as they boarded the platform. But here again the pictures don’t point to that solution. John Cupis, a friend who spent his childhood at Staines, Middlesex, tells me that on the London lowbridge STs there was a gap in front of the rearmost seat upstairs to allow you to cross between gangways, but that "you had to stoop" as you crossed.
The Luton top decks look to be built as far forward over the cab as possible, presumably to accommodate the 9 rows of seats necessary to get 26 upper-deck seats.
Thanks for the photo and detailed account of this very unusual and characterful batch. Luton Corporation always seemed to go for something different!

Ian Thompson


18/02/11 – 11:35

A rare commodity indeed was the BET "Federation" style double decker. Single deckers were common, but there were few double deckers, the 3 window front top deck being a feature.
Common with East Yorkshire, built by Brush and ECW. Also Thames Valley?
YWD had a few. Who else?
The Willowbrook body here has more of a bay window effect, as Chris points out, but perhaps was influenced by the BET ideas, although by no means a regular Willowbrook feature.

John Whitaker


19/02/11 – 06:47

That front upper-deck window seems particularly appropriate to the symmetrical double-gangway layout. Front seat passengers must indeed have felt as if they were sitting on a sofa looking through a bay window!
The Daimler COG was years ahead of its time in terms of refinement. They did indeed have flexible engine mountings, and John’s description (apart from the creaking bodywork) could equally well apply to a Daimler CVG built many years later. Manchester bought COGs and CVGs from 1940 to 1963, and there was hardly any difference in the riding experience at all.

Peter Williamson


20/02/11 – 08:21

I’m grateful to John Cupis for sending me photos, taken 60-odd years ago by the late John C. Gilham, of London Transport lowbridge STs, both outside and INSIDE! To read the rest of my comment and see the great shots click here.

Ian Thompson


25/05/11 – 06:33

I suspect that this vehicle was already being used for spares as it has already lost one headlight. Did these buses ever have the engine side panel closed. I can imaging some of the drivers cursing the 5LW engine on Crawley Green as not only is it very steep, it is also lengthy and had a bus stop at the foot. A dead start on a Saturday lunch time outbound with a full load of seated passengers and probably another half dozen standing would mean 5 minutes climbing in first gear with speed probably in single figures.

David Manning


25/05/11 – 16:58

The pre-selector boxes made a wonderful, tuneful sound with variation of pitch, especially on overrun: and when stationary, they would have a distinctive "hunt" as a reminder to get a move on!

Joe


26/05/11 – 07:29

Joe, unless I’m mistaken (I’m no engineer) I believe that the delightful symphony while standing, and it WAS delightful – in neutral – emanated from the fluid flywheel rather than from the preselctor gearbox.

Chris Youhill


27/05/11 – 08:40

I’m sure you are right Chris- I should have said "transmission"!

Joe


05/08/13 – 17:48

My father worked as a conductor for many years with Luton Corporation buses he received a gold watch for 25yr service but died shortly after receiving it.

Walter Gunning


 

Quick links to the  -  Comments Page  -  Contact Page  -  Home Page

 


 

Rochdale Corporation – AEC Reliance – GDK 324D – 24

Rochdale Corporation - AEC Reliance - GDK 324D

Rochdale Corporation
1966
AEC Reliance 6MU2RA
Willowbrook B45F

Rochdale were always a good customer for AEC vehicles especially single deckers all from 1940 were AEC. Front engined Regals to start with to rear engined Swifts with the very dependable underfloor Reliance in between, the above does look quite smart with its Willowbrook body. I do like the roof windows I should imagine that they made the bus feel quite bright and airy. This vehicle passed over to SELNEC on the 1st of November 1969 and probably did many years service with them. The Reliance coding is bit tricky to understand a MU2RA had a synchromesh gearbox and vacuum brakes, what the 6 stood for I do not know, engine size perhaps, if anyone knows all the Reliance coding and what they all stood for please let me know and I will put them on the abbreviations page.

Photograph contributed by Ian Beswick

———

Thanks to David Oldfield for putting together the codes for the AEC Reliance which can be seen here.

———

The 6MU2RA had Monocontrol gearboxes and air brakes as had all Rochdale’s Reliances. In the AEC code no 3 stands for Synchromesh and ‘V’ for vacuum brakes. Also Rochdale’s Regals were not front engined but underfloor engined Regal IV’s. They were 1-7 with East Lancs bodies (1951) and 8-15 with Burlingham bodies (1953). All were delivered as B42D but were converted in the late 1950’s to B44F.
Four (11/13-15) were sold to Lancaster City Transport around 1957 as the Healey route 2 was converted to double-deck operation and Rochdale had less need for saloons.

Philip Halstead


 

Quick links to the  -  Comments Page  -  Contact Page  -  Home Page

 


 

All rights to the design and layout of this website are reserved     

Old Bus Photos from Saturday 25th April 2009 to Wednesday 3rd January 2024